Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

Options
Go to last post Go to first unread
smackover  
#1 Posted : Saturday, October 6, 2018 5:55:17 PM(UTC)
smackover

Rank: Member

Groups: Registered
Joined: 7/14/2015(UTC)
Posts: 7

Was thanked: 1 time(s) in 1 post(s)
Hello, hoping for some guidance here. I have the above dryer and the igniter is not lighting at all. Clothes have been taking a long time to dry the past couple of weeks and finally no heat today.

I have checked continuity on the following items and all have checked out okay.

1. Thermal fuse checks out okay
2. Igniter (reads 75 ohms)
3. Gas solenoids tested good. I replaced anyway but no change
4. Flame sensor checks out okay
5. High limit thermostat checks out okay
6. Cycling thermostat. I can't find it to check it. Haven't taken the dryer completely apart yet.
7. Thermistor (adjacent to the thermal fuse) reads about 9 ohms

Questions:

1. Is there a cycling thermostat on my dryer? I assume there is as the unit has several heat settings.

2. Can the igniter test good and be bad?

Please help.

Thanks
Cameron
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
smackover  
#2 Posted : Monday, October 8, 2018 10:27:56 AM(UTC)
smackover

Rank: Member

Groups: Registered
Joined: 7/14/2015(UTC)
Posts: 7

Was thanked: 1 time(s) in 1 post(s)
Anyone?

I did more troubleshooting over the weekend and here is where I'm at now:

1. Bench tested the igniter and it lights
2. Thermister reads between 9-10 ohms
3. Thermal fuse, gas solenoids, HL Thermo test okay.

I even went so far as to take the centrifigal switch apart at the motor and clean the contacts.

I still don't have a glowing igniter when starting the dryer. I'm at a complete loss as to where to go from here.

Any assistance is greatly appreciated.
Billy889  
#3 Posted : Monday, October 8, 2018 4:45:24 PM(UTC)
Billy889

Rank: Member

Groups: Registered
Joined: 9/29/2018(UTC)
Posts: 17

Up! Good One
UserPostedImage
smackover  
#4 Posted : Monday, October 8, 2018 11:07:00 PM(UTC)
smackover

Rank: Member

Groups: Registered
Joined: 7/14/2015(UTC)
Posts: 7

Was thanked: 1 time(s) in 1 post(s)
I finally found the problem. It was the heater relay switch up in the control housing. I found a troubleshooting guide online that suggested checking the relay switch if all the switches and thermostats check out okay.

I’m surprised there was limited information on the relay switch online. It’s probably because they don’t fail for a very long time and the issue is generally one of the 5 switches/thermostat.

To test the relay just swap the start button relay with the heater relay (they are the same exact relay) and see if you get heat. You have to hold the start button down by hand because it’s the only way the dryer will stay running with the faulty relay now being used by the start button. I hope this information helps someone.
thanks 1 user thanked smackover for this useful post.
OLDJAY on 10/22/2018(UTC)
Users browsing this topic
Guest (2)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.