Flustered by error messages Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: 11022062100	Brand: Kenmore	Age: 5 - 10 years
Previous Topic Next Topic

napradoc		#1 Posted : Monday, March 8, 2010 5:49:53 AM(UTC)
Rank: Member Groups: Registered Joined: 4/29/2008(UTC) Posts: 10		Kenmore elite Calypso motion washer, I do not have the owners manual. Lately I have been getting error messages of C1 or is it CL, and also FL. Seems to stick on these messages, if I unplug it for several hours and then restart it, it SOMETIMES continues to run. Any suggestions or help would be appreciated. Steve
User Profile View All Posts by User View Thanks

Sponsor
	See inside of your appliance - diagrams and part photos for virtually every model. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com

sidfink43		#2 Posted : Tuesday, March 9, 2010 4:13:13 PM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 3/29/2009(UTC) Posts: 11,699		See if you can use this service manual to put it into test/diagnosis mode and determine what the issue is. https://secured.whirlpoo...4632a4/$FILE/8178010.pdf
User Profile View All Posts by User View Thanks

napradoc		#3 Posted : Monday, March 15, 2010 4:54:25 AM(UTC)
Rank: Member Groups: Registered Joined: 4/29/2008(UTC) Posts: 10		Thanks for the manual, I ran it through the dianostic tests but nothing came up. Still getting error messages of LD,CL, and especially FL. Still have to unplug it for quite a while before it will pump out the water and start running again. Any other suggestions would be appreciated. !! Steve
User Profile View All Posts by User View Thanks

sidfink43		#4 Posted : Monday, March 15, 2010 5:35:49 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 3/29/2009(UTC) Posts: 11,699		In this situation you want to do things that cost the least amount of money. I would start by taking off the pump and thoroughly cleaning it out along with the drain hoses. Let's see what that does, if anything, for you.
User Profile View All Posts by User View Thanks

napradoc		#5 Posted : Monday, March 15, 2010 6:08:52 AM(UTC)
Rank: Member Groups: Registered Joined: 4/29/2008(UTC) Posts: 10		Thanks, I'll give it a try. I've also noticed that after letting it sit and plugging it back in the FL message flashes and it just hums. Does this change your approach any?? Steve
User Profile View All Posts by User View Thanks

sidfink43		#6 Posted : Monday, March 15, 2010 6:17:25 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 3/29/2009(UTC) Posts: 11,699		Everything you state points to a machine control board problem, but since that is pretty expensive and requires a replacement to confirm, try the cleanout first, and also take off and clean and reseat all the connections.
User Profile View All Posts by User View Thanks

napradoc		#7 Posted : Monday, March 15, 2010 9:53:17 AM(UTC)
Rank: Member Groups: Registered Joined: 4/29/2008(UTC) Posts: 10		O.K. I haven't tried to clean it out yet, but when I run the self diagnosis program the countdown timer stops at 33. Does this help give you a better idea about whats going on. Steve
User Profile View All Posts by User View Thanks

sidfink43		#8 Posted : Monday, March 15, 2010 11:37:03 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 3/29/2009(UTC) Posts: 11,699		Sorry, same opinion, if cleaning the drain/pum and the connections and reseating them does not help I am afraid you will have to try with a control replacement.
User Profile View All Posts by User View Thanks

napradoc		#9 Posted : Monday, March 15, 2010 12:17:24 PM(UTC)
Rank: Member Groups: Registered Joined: 4/29/2008(UTC) Posts: 10		Would that be the electronic control board or the motor control board you are talking about, not sure which one you mean. steve
User Profile View All Posts by User View Thanks

sidfink43		#10 Posted : Monday, March 15, 2010 12:30:13 PM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 3/29/2009(UTC) Posts: 11,699		Main Control Board should be the source of the problem. Hopefully it won't come to that.
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (5)