Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

Options
Go to last post Go to first unread
jwysocky  
#1 Posted : Saturday, February 20, 2010 10:28:06 AM(UTC)
jwysocky

Rank: Member

Groups: Registered
Joined: 2/20/2010(UTC)
Posts: 5

My GE electric dryer timer won't advance in the automatic modes.(DRXR473EWOWW). I replaced the timer in a recent purchase from APP.com:(. The dryer dries in all modes, but the timer only advance in the timed drying mode which is OK, so it is usable. I see in the parts list a resistor and thermostats, but have no idea where to go from here. I've cleaned all the duct work front and back.

Thanks
John
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
jwysocky  
#2 Posted : Tuesday, February 23, 2010 5:40:31 AM(UTC)
jwysocky

Rank: Member

Groups: Registered
Joined: 2/20/2010(UTC)
Posts: 5

Come on guys, someone must have an idea of whats wrong.

John:)
denman  
#3 Posted : Tuesday, February 23, 2010 6:14:19 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Cannot find any info using given model number.

When you replaced the timer did you find the wiring diagram in the control console?

How this often works is that in Auto modes the timer motor gets power through the heating coil when the heating coil is turned off.

The resistor you mentioned may be there to drop the heater voltage from 240 to 120 for the timer motor.

Remove it and check it for continuity, usually 5,000 to 10,000 ohms.

Also check that the temp settings actually change the temperatures.
You may have a grounded element re: the element never turns off.
THIS FORUM IS DEAD!!!!!!!
jwysocky  
#4 Posted : Tuesday, February 23, 2010 6:25:45 AM(UTC)
jwysocky

Rank: Member

Groups: Registered
Joined: 2/20/2010(UTC)
Posts: 5

DRXR473EWOWW This number is listed above.

I have the wiring diagram and will check the resister. If you put the auto near the end of the cycle it will work and the heat will not be on.

Thank you John
denman  
#5 Posted : Tuesday, February 23, 2010 7:19:48 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Yes I saw the model number just cannot find any info.

Does sound like it may be a grounded element, wish I had the wiring diagram.
At the end of an Auto cycle the unit goes into cool down to prevent wrinkling and shuts the heater off using a set of timer contacts.
Note: Some GE's use dual elements so if one of them burns out you will stall have heat but no timer advance.

Check the heating coil.
Unplug the unit and both wires to the coil.
Check it with a meter, should be around 12 ohms.
Then check from each side of the coil to the case/frame, both should be infinite ohms (open). If not the coil may have sagged or broken and is touching the case.
THIS FORUM IS DEAD!!!!!!!
jwysocky  
#6 Posted : Tuesday, February 23, 2010 8:52:21 AM(UTC)
jwysocky

Rank: Member

Groups: Registered
Joined: 2/20/2010(UTC)
Posts: 5

If you have a fax no. I can fax wiring diagram to you if that will help. the wiring diagram does show a inner and outer heating coil. My question is do I remove a side panel to get to the heating element?
denman  
#7 Posted : Tuesday, February 23, 2010 1:20:15 PM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Often you can get at them from the top depending on the dryer.

Perhaps the following will help
http://www.applianceaid.com/ge-dryers.html
THIS FORUM IS DEAD!!!!!!!
jwysocky  
#8 Posted : Thursday, February 25, 2010 1:54:49 PM(UTC)
jwysocky

Rank: Member

Groups: Registered
Joined: 2/20/2010(UTC)
Posts: 5

If it happens to be a heating element, I'm not going to put another $200 into and old washer. I already made a mistake thinking it was the timer $80 dollar latter I'm no further ahead and a Repairman will probable be in the $400 range.. I just keep using it till the other heating element quits. thanks for trying

John
Users browsing this topic
Guest (2)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.