Maytag Front Loader not dispensing bleach or fabric softner - Appliance Repair Forum

Welcome Guest! You can not login or register.

Notification

Error

Maytag Front Loader not dispensing bleach or fabric softner Options Email this topic Watch this topic Print this topic » Normal Threaded
Model: MHWE201YW00	Brand: Maytag	Age: 1 - 5 years
Previous Topic Next Topic

Ron1404		#1 Posted : Sunday, December 18, 2016 3:42:55 PM(UTC)
Rank: Member Groups: Registered Joined: 12/18/2016(UTC) Posts: 3		Bleach or fabric softner will not dispense. I have ensured outlets are all clear of buildup. I removed the top panel and observed action through wash cycle. On what should be bleach cycle and what should be the fabric softner rinse, it appears the water just trickles in vs. a rush. It's like a valve is only partially opening. Any ideas on what repair may be.


User Profile View All Posts by User View Thanks

Sponsor

See inside of your appliance - diagrams and part photos for virtually every model.

ThatGuy		#2 Posted : Sunday, December 18, 2016 10:11:03 PM(UTC)
Rank: Advanced Member Groups: Expert Joined: 7/27/2010(UTC) Posts: 1,395 Location: near the middle of nowhere Was thanked: 24 time(s) in 24 post(s)		It might be gunk clogging up the inlet screen or it could be a bad water valve. Parts 1 and 2 on this diagram. The single valve is the hot water one. The dual valve is cold. Parts for Maytag MHWE201YW00 / : Dispenser Parts - AppliancePartsPros.com


User Profile View All Posts by User View Thanks

Ron1404		#3 Posted : Monday, December 19, 2016 5:14:56 AM(UTC)
Rank: Member Groups: Registered Joined: 12/18/2016(UTC) Posts: 3		Thanks. I did check the inlet water screens and they were fine. We are on municipal water so did not expect clogs. The hot water valve is the one trickling at that rinse but that makes sense (hot would not be on for that rinse). So is most likely the cold valve. Is it possible that one side of the dual not be working? I ask because when dispensing detergent is not issue at all.


User Profile View All Posts by User View Thanks

ThatGuy		#4 Posted : Monday, December 19, 2016 8:29:23 AM(UTC)
Rank: Advanced Member Groups: Expert Joined: 7/27/2010(UTC) Posts: 1,395 Location: near the middle of nowhere Was thanked: 24 time(s) in 24 post(s)		Yes, you could have one side of the valve bad. Their are two coils on the dual valve and two outlets, so one coil could be bad or one side could be plugged up. That's what I think you have. One side of your cold water valve is partially plugged up inside. If you saw how tight the tolerances were inside the valve, you would realize it doesn't take much to stop them from working right. And yet its usually one of the most durable parts on the machine. On this picture the gray parts are the solenoid coils. The blue part contains the inlet and outlets of the valve.


User Profile View All Posts by User View Thanks

Ron1404		#5 Posted : Tuesday, December 20, 2016 4:24:42 PM(UTC)
Rank: Member Groups: Registered Joined: 12/18/2016(UTC) Posts: 3		Thank you! I will pull the valve and check for plugging. If none apparent, will just replace the valve. You have been a great help!


User Profile View All Posts by User View Thanks

ThatGuy		#6 Posted : Wednesday, December 21, 2016 10:12:04 AM(UTC)
Rank: Advanced Member Groups: Expert Joined: 7/27/2010(UTC) Posts: 1,395 Location: near the middle of nowhere Was thanked: 24 time(s) in 24 post(s)		Those valves are sealed at the factory, so your best bet is to replace it. Good Luck. :)


User Profile View All Posts by User View Thanks

Users browsing this topic
Guest (4)

Forum Jump

You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Important Information: The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies. More Details Close