Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

2 Pages<12
Options
Go to last post Go to first unread
walt0132  
#11 Posted : Wednesday, February 25, 2015 9:14:31 PM(UTC)
walt0132

Rank: Member

Groups: Registered
Joined: 4/24/2012(UTC)
Posts: 20

The red wire on the bottom reads ~120V, the red & white wire on the top read nil.

I also unplugged the dryer, disconnected the leads from the heating element and tested for continuity of the element. The meter didn't register a value for resistance - I think this means it was an open circuit?

So am I right in assuming that the element is bad? What was the "other" problem you referred to?
fairbank56  
#12 Posted : Thursday, February 26, 2015 5:18:35 AM(UTC)
fairbank56

Rank: Advanced Member

Groups: Expert
Joined: 10/16/2012(UTC)
Posts: 3,806

Was thanked: 7 time(s) in 7 post(s)
Yes, the element is open but there is also an open circuit somewhere between the timer and the red/white wire. Need to check continuity on the thermal cutoff, hi limit thermostat and operating thermostat.

http://www.appliancepartspros.c...t-3387747-ap2947033.html

Eric
walt0132  
#13 Posted : Thursday, February 26, 2015 5:29:32 AM(UTC)
walt0132

Rank: Member

Groups: Registered
Joined: 4/24/2012(UTC)
Posts: 20

What values should I be checking for? Just continuity?
fairbank56  
#14 Posted : Thursday, February 26, 2015 5:38:53 AM(UTC)
fairbank56

Rank: Advanced Member

Groups: Expert
Joined: 10/16/2012(UTC)
Posts: 3,806

Was thanked: 7 time(s) in 7 post(s)
Yes, they are just switches. On the operating thermostat, check between the red and red/white wire, not the blue wires.
walt0132  
#15 Posted : Thursday, February 26, 2015 6:06:08 AM(UTC)
walt0132

Rank: Member

Groups: Registered
Joined: 4/24/2012(UTC)
Posts: 20

Ok, checked all 3 switched. All checked out fine. After thinking back to something you said earlier ("Place dryer in air only cycle..."), I had been testing the element with the dryer on a setting where the heat wasn't on. After running it on a different setting, I got ~120V on both leads into the element. Sorry, my mistake - I guess I was just being dumb and am a little unfamiliar with the internals of the dryer.

So if all 3 switches test OK and both leads into the element read ~120V, that should mean the element is the only bad part, right?
fairbank56  
#16 Posted : Thursday, February 26, 2015 6:16:44 AM(UTC)
fairbank56

Rank: Advanced Member

Groups: Expert
Joined: 10/16/2012(UTC)
Posts: 3,806

Was thanked: 7 time(s) in 7 post(s)
Ah, yes, assumed you were in heat cycle. Looks like heat element is the only culprit.

Eric
walt0132  
#17 Posted : Thursday, February 26, 2015 6:23:55 AM(UTC)
walt0132

Rank: Member

Groups: Registered
Joined: 4/24/2012(UTC)
Posts: 20

Ok, good. Was hoping I was right about that. Eric, thanks a bunch for all of your help!
Users browsing this topic
Guest (2)
2 Pages<12
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.