Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

Options
Go to last post Go to first unread
rangerjoey76  
#1 Posted : Sunday, December 8, 2013 11:55:34 AM(UTC)
rangerjoey76

Rank: Member

Groups: Registered
Joined: 12/8/2013(UTC)
Posts: 5

My washer won't agitate. It will drain the water and then just sit there with the pump still running. I checked the belt, its in good condition. I checked the lid switch and it is working property. Motor and pully move freely. What next?
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
rangerjoey76  
#2 Posted : Sunday, December 8, 2013 11:57:40 AM(UTC)
rangerjoey76

Rank: Member

Groups: Registered
Joined: 12/8/2013(UTC)
Posts: 5

Also it doesn't seem like the motor is trying to run or do anything. Does this model have fuse or something I can check? This model doesn't have any light indicators on it.
fairbank56  
#3 Posted : Sunday, December 8, 2013 12:21:47 PM(UTC)
fairbank56

Rank: Advanced Member

Groups: Expert
Joined: 10/16/2012(UTC)
Posts: 3,806

Was thanked: 7 time(s) in 7 post(s)
No fuse on this model. Check the motor connector for burned/corroded wire terminals or broken wire at terminal connections. My information shows this washer having several status LED's. Pull the tech sheet from inside the control panel. It will tell you how to get into service mode to check for any error codes but they are displayed using the status LED's. Do you have a multimeter and experience using it to check voltages at motor connector?

Eric
rangerjoey76  
#4 Posted : Monday, December 9, 2013 4:53:39 AM(UTC)
rangerjoey76

Rank: Member

Groups: Registered
Joined: 12/8/2013(UTC)
Posts: 5

I have a multi meter, but can't say that I am that experienced at what you are asking.
rangerjoey76  
#5 Posted : Monday, December 9, 2013 6:13:19 AM(UTC)
rangerjoey76

Rank: Member

Groups: Registered
Joined: 12/8/2013(UTC)
Posts: 5

No power going to the motor at all. All switches seem to be working properly. Talking to my local appliance repair store we have narrowed it down to replacing the main control board. At $180 this doesn't seem very practical for a 15 year old washer.
fairbank56  
#6 Posted : Monday, December 9, 2013 6:44:34 AM(UTC)
fairbank56

Rank: Advanced Member

Groups: Expert
Joined: 10/16/2012(UTC)
Posts: 3,806

Was thanked: 7 time(s) in 7 post(s)
Check for 120vac at the control board 6-pin connector between the yellow wire and the red/white wire. If you have 120vac there, washer fills and drains but never any noise from the motor, then I agree that it's the control board.

Eric
rangerjoey76  
#7 Posted : Monday, December 9, 2013 7:05:31 AM(UTC)
rangerjoey76

Rank: Member

Groups: Registered
Joined: 12/8/2013(UTC)
Posts: 5

Yup, 120 volts there, thanks.
Users browsing this topic
Guest (2)
Similar Topics
ge washer wont spin or agitate (Washer Repair)
by outback32 9/29/2015 9:46:08 AM(UTC)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.