Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
Dishwasher dead
Options
Go to last post Go to first unread
Model: KUDI02CRBS1 Brand: Kitchen Aid Age: 5 - 10 years
Previous Topic Next Topic
Behinz  
#1 Posted : Sunday, November 24, 2013 8:33:51 AM(UTC)
Behinz

Rank: Member

Groups: Registered
Joined: 11/24/2013(UTC)
Posts: 4
Checked thermal fuse, power to dishwasher, checked microswitch at door, replaced main circuit board-touchpad still will not work. Any other suggestions
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
denman  
#2 Posted : Monday, November 25, 2013 2:21:45 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Here are your parts
Parts for Whirlpool KUDI02CRBS1 Dishwasher - AppliancePartsPros.com

See the attachment for the tech sheet.

If I understand your post correctly both the control board (item 11 in section 02) and the console/keypad (item 1 in section 02) have been replaced.

Re-check the thermal fuse just in case it is blowing as soon as power is applied to the unit.

if OK.
Check the tracks for continuity in the ribbon cable and interconnect PCB (items 3 & 2 in section 02).

Have you for power at the control board, just in case there is a bad connection/wire from the electrical connect box up to the control board?
I have seen where there has been a problem with a wire nut connection after several years of use.
File Attachment(s):
KUDI02C.pdf (244kb) downloaded 11 time(s).
THIS FORUM IS DEAD!!!!!!!
Back to top
Behinz  
#3 Posted : Monday, November 25, 2013 3:43:28 PM(UTC)
Behinz

Rank: Member

Groups: Registered
Joined: 11/24/2013(UTC)
Posts: 4
I have not yet replaced the flexible control button touch panel, I did put a new board in, fuse and door micro switch check out good. Reseated all ribbon connectors, no sign of corrosion anywhere. Did not check float level switch, as did not think this could cause the panel to go blank No lights.

Interesting though, when I have the door open and depress the door microswitch down, in about 3 seconds I will hear a noise coming from the DW. But then after a minute or two it quits then nothing else, still no lights on keypad.

I wanted to make sure I actually need a 100$ keypad before I have to eat another expensive part.
Back to top
denman  
#4 Posted : Tuesday, November 26, 2013 12:36:53 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
You cannot really tell if a ribbon cable is OK just by looking at it.
You have to measure each track with a meter.
A fairly common problem with them is that they can develop hair line cracks across the copper tracks.
Theses can be hard to see even using a magnifying glass.
THIS FORUM IS DEAD!!!!!!!
Back to top
Behinz  
#5 Posted : Tuesday, November 26, 2013 1:50:24 AM(UTC)
Behinz

Rank: Member

Groups: Registered
Joined: 11/24/2013(UTC)
Posts: 4
Do I have to disconnect each ribbon cable and do continuity tests on each single pin? At least one is hardwired.
Back to top
denman  
#6 Posted : Tuesday, November 26, 2013 4:35:27 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
You could just disconnect it at/from the control board.

And then check the key pinouts as per the tech sheet.
This will then chech the complete control pane circuitry.

If you find a problem then you can disconnect what yo can to try to find where the problem is.
THIS FORUM IS DEAD!!!!!!!
Back to top
Behinz  
#7 Posted : Sunday, December 1, 2013 11:54:13 AM(UTC)
Behinz

Rank: Member

Groups: Registered
Joined: 11/24/2013(UTC)
Posts: 4
It was the contol panel touchpad that was bad. I did the hair dryer thing and could not bring it back to life so I ordered a new one from the link from this site. Got here quick, good price and well packed. Everything else checked out so this HAD to be it! I have had this thing apart so many times now it only took 20 minutes to replace it and have it up and running. Thanks for your help here all.

Bill in GA.
Back to top
Users browsing this topic
Guest (2)
Similar Topics
GE Dishwasher dead UI board (Dishwasher Repair)
by Guest 1/26/2023 9:44:03 PM(UTC)
Dishwasher dead? (Dishwasher Repair)
by Guest 1/9/2022 8:49:13 AM(UTC)
Maytag dishwasher dead (Dishwasher Repair)
by archer75 1/25/2018 7:13:29 PM(UTC)
Kenmore dishwasher dead (Dishwasher Repair)
by cameo4352 6/26/2015 4:59:43 AM(UTC)
Dishwasher dead, other posts not solving (Dishwasher Repair)
by trehltom 11/22/2013 11:40:27 AM(UTC)
Maytag Dishwasher Dead in the Water (Dishwasher Repair)
by Mr B 2/6/2013 2:17:12 PM(UTC)
Maytag protable dishwasher dead (Dishwasher Repair)
by redcrd 1/7/2013 9:00:24 AM(UTC)
Kenmore Dishwasher dead (Dishwasher Repair)
by tonyk1961 5/1/2012 9:34:37 AM(UTC)
2yo Kenmore dishwasher dead (Dishwasher Repair)
by teachermom 4/30/2012 5:15:10 PM(UTC)
Maytag dishwasher dead (Dishwasher Repair)
by dadofthree 4/15/2012 8:40:47 PM(UTC)
dishwasher dead - no lights (Dishwasher Repair)
by wishfully17 3/20/2012 9:08:29 AM(UTC)
Kenmore dishwasher dead (Dishwasher Repair)
by Mike12 1/6/2012 2:08:20 PM(UTC)
Dishwasher dead KitchenAid KUDS01IJBS0 (Dishwasher Repair)
by Master Chief 9/25/2011 8:00:20 AM(UTC)
dishwasher dead (Dishwasher Repair)
by brankulo 1/25/2011 6:06:32 AM(UTC)
Dishwasher dead (Dishwasher Repair)
by sonnydaze69 2/24/2010 9:43:45 AM(UTC)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET