Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
Maytag Spin Problem
Options
Go to last post Go to first unread
Model: SAV2555AWW Brand: Maytag Age: 1 - 5 years
Previous Topic Next Topic
big red 2000  
#1 Posted : Wednesday, December 26, 2007 8:15:30 AM(UTC)
big red 2000

Rank: Member

Groups: Registered
Joined: 12/26/2007(UTC)
Posts: 3
I have a Maytag top loading wash machine. When it goes into the spin cycle it makes a fast loud popping noise (water is draining but tub is not spinnning). I looked at it and the plastic helix on the very bottom of the drive was not staying engaged in the spin cycle. It engages fine in wash mode. I replace the spin pulley and plastic helix thinking it was just worn out. Worked great for about three weeks and now it is doing the exact same thing again. Any advice?
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
Gene  
#2 Posted : Wednesday, December 26, 2007 12:25:28 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
Most likely the problem with your washer is a bad triple lip seal.

You can find the complete instructions how to replace the triple lip seal and bearing in the Maytag bulletin.

You will need a few special tools. The part numbers you can find in the bulletin.

- The part number for the triple lip seal and bearing assembly is
AP4260929

Good luck.
Gene.
Back to top
big red 2000  
#3 Posted : Wednesday, December 26, 2007 3:42:43 PM(UTC)
big red 2000

Rank: Member

Groups: Registered
Joined: 12/26/2007(UTC)
Posts: 3
After I read your response I looked at my machine again. I noticed that the shaft moves up and down about a half an inch. I am assuming that it shouldn't and that's why the small plastic helix is not engaging during the spin cycle. Am I correct. :)
Back to top
big red 2000  
#4 Posted : Wednesday, December 26, 2007 3:51:36 PM(UTC)
big red 2000

Rank: Member

Groups: Registered
Joined: 12/26/2007(UTC)
Posts: 3
After I read your response I looked at my machine again. I noticed that the shaft moves up and down about a half an inch. I am assuming that it shouldn't and that's why the small plastic helix is not engaging during the spin cycle. Am I correct.
Back to top
Gene  
#5 Posted : Wednesday, December 26, 2007 5:53:15 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
Sounds like a bad transmission.

Gene.
Back to top
Users browsing this topic
Guest (3)
Similar Topics
Maytag spin problem (Washer Repair)
by kingbrewster 1/12/2012 7:07:36 AM(UTC)
maytag spin problem (Washer Repair)
by djcrazytaxi 3/25/2011 7:33:12 PM(UTC)
Maytag spin problem (Washer Repair)
by vulcanman 8/15/2009 2:37:01 PM(UTC)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET