Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

Options
Go to last post Go to first unread
Maverick1  
#1 Posted : Wednesday, December 6, 2017 6:29:07 AM(UTC)
Maverick1

Rank: Member

Groups: Registered
Joined: 12/6/2017(UTC)
Posts: 2

My issue started with my wife noticing that the dryer was running cold. I then took the following steps:
1. Checked for airflow outside the house. It was blowing cool air
2. Used my leaf blower to blow air through the air duct and check for blockage. Very little came out.
3. Checked the hose. Not perfect, but nothing visible clogging it. It does have to snake around creating two turns, but it has been like this for a while with no issues.
4. Checked the element. No breaks. Nothing touched the metal housing. Element has continuity.
5. Checked the thermostat and thermal fuse (the two fuses on the element housing. Not sure the technical names.) The little one (thermal fuse) has no continuity the bigger one was fine. I figured it must have been tripped.
6. I replaced the thermal fuse. Dryer worked for five minutes. Seemed to run hot. After five minutes it turned cold. Checked the new thermal fuse and it was tripped.

For some reason the element is overheating the dryer and tripping the fuse. I then did a continuity with one end of the element and directly on the housing to test for a ground issue and got no continuity. Which is good, correct?

At a loss at what to do now? Is it worth replacing the element (just replaced this summer) if everything is testing out with it? Is there another fuse or thermostat somewhere? Can the other thermostat be an issue if it has continuity?

Thanks in advance
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
thorning  
#2 Posted : Wednesday, December 6, 2017 8:52:37 AM(UTC)
thorning

Rank: Member

Groups: Registered
Joined: 8/25/2012(UTC)
Posts: 248

There is a high limit t-stat on most dryers that should limit the heating. This is one you may need to find and check. Usually the thermal fuse trips because of a restriction in the outlet vent tube. Suggest you runs the dryer with the vent tube disconnected completely after you replace or bypass the thermal fuse.
Maverick1  
#3 Posted : Wednesday, December 6, 2017 5:28:58 PM(UTC)
Maverick1

Rank: Member

Groups: Registered
Joined: 12/6/2017(UTC)
Posts: 2

The high limit has continuity. Also I bypassed the thermal fuse and ran it. The outgoing air measured 165 then down to about 135 then up again. Cycle five or six times. Is that range OK? Currently assuming the problem was the hose partially blocked. Just hard to believe since it didn't look too bad. Any thoughts?
thorning  
#4 Posted : Wednesday, December 6, 2017 6:35:39 PM(UTC)
thorning

Rank: Member

Groups: Registered
Joined: 8/25/2012(UTC)
Posts: 248

Originally Posted by: Maverick1 Go to Quoted Post
The high limit has continuity. Also I bypassed the thermal fuse and ran it. The outgoing air measured 165 then down to about 135 then up again. Cycle five or six times. Is that range OK? Currently assuming the problem was the hose partially blocked. Just hard to believe since it didn't look too bad. Any thoughts?


That temp is about right based on some testing I did on a dryer recently. The thermal fuse blows when the air flow is blocked or significantly restricted. I changed one today and the amount of stuff in the blower air flow was considerable.
Users browsing this topic
Guest (2)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.