Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
GE Profile Washer Stops during filling & wont rinse
Options
Go to last post Go to first unread
Brand: GE Age: 5 - 10 years
Previous Topic Next Topic
KLS2015  
#1 Posted : Sunday, March 22, 2015 7:26:19 PM(UTC)
KLS2015

Rank: Member

Groups: Registered
Joined: 3/22/2015(UTC)
Posts: 7
GE Profile Washer stops filling midway through the initial fill cycle- on Cold. Must change to Hot water for system to restart. System stops again at beginning of Rinse cycle.
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
sidfink43  
#2 Posted : Monday, March 23, 2015 10:22:33 AM(UTC)
sidfink43

Rank: Advanced Member

Groups: Senior Expert
Joined: 3/29/2009(UTC)
Posts: 11,699
If you will post a model number so that we can see exactly what machine you have someone should be able to help you.

Thanks
Back to top
KLS2015  
#3 Posted : Monday, March 23, 2015 10:28:26 AM(UTC)
KLS2015

Rank: Member

Groups: Registered
Joined: 3/22/2015(UTC)
Posts: 7
GE Profile Washer
Model # WPRE6100GOWT
Back to top
sidfink43  
#4 Posted : Monday, March 23, 2015 3:04:54 PM(UTC)
sidfink43

Rank: Advanced Member

Groups: Senior Expert
Joined: 3/29/2009(UTC)
Posts: 11,699
OK, good. This model has a mode shifter and an inverter with a blinking light on the inverter that gives error codes.

Here is a link to the interpretation of the error codes. The first thing to do is a reset, sometimes that is all that is needed.

HydroWave GE Washer Repair Guide
Back to top
KLS2015  
#5 Posted : Monday, March 30, 2015 7:29:27 AM(UTC)
KLS2015

Rank: Member

Groups: Registered
Joined: 3/22/2015(UTC)
Posts: 7
Hello Again. I completed the Reset. When washer reached the Rinse cycle, it did completely fill.... Which is an improvement. It would only fill half way previously.

However, after filling on rinse cycle the unit shuts off. To complete the wash, we must turn selector to Drain/Spin and Restart.

Thank you
Back to top
sidfink43  
#6 Posted : Monday, March 30, 2015 8:59:46 AM(UTC)
sidfink43

Rank: Advanced Member

Groups: Senior Expert
Joined: 3/29/2009(UTC)
Posts: 11,699
Ok, try the reset again, and if that does not fix things check the error codes.
Back to top
KLS2015  
#7 Posted : Saturday, April 4, 2015 8:48:04 PM(UTC)
KLS2015

Rank: Member

Groups: Registered
Joined: 3/22/2015(UTC)
Posts: 7
The Reset process worked for 2-3 wash loads. The unit then reverted back to original issue, ie., Stopped at Rinse cylce. Would not fill. This also occurred for 2 loads.

Then washer would not fill at initial start.

Tried "Reset" again.... no change.
Back to top
sidfink43  
#8 Posted : Sunday, April 5, 2015 4:13:58 AM(UTC)
sidfink43

Rank: Advanced Member

Groups: Senior Expert
Joined: 3/29/2009(UTC)
Posts: 11,699
The problem could be the motor/inverter or the control board. I suspect the control board so go ahead and replace it. If you buy the part from this site and it does not fix the problem you can return it.
Back to top
KLS2015  
#9 Posted : Monday, June 15, 2015 7:25:38 PM(UTC)
KLS2015

Rank: Member

Groups: Registered
Joined: 3/22/2015(UTC)
Posts: 7
Hello Again.... After some time traveling I finally got the replacement Board ordered and installed. The swap-out went well...no problems. However, the washer still Stops and will not fill for the Rinse cycle. (We fill the tub by hand, then rotate dial to Drain/Spin to complete the cycle.

I tried the Reset --Opening/Closing lid method, with no change in results.

Hopefully, you have another magic solution.
Thank you

Les
Back to top
KLS2015  
#10 Posted : Wednesday, June 24, 2015 3:40:26 PM(UTC)
KLS2015

Rank: Member

Groups: Registered
Joined: 3/22/2015(UTC)
Posts: 7
Hello Again.... After some time traveling I finally got the replacement Board ordered and installed. The swap-out went well...no problems.

However, the washer still Stops and will not fill for the Rinse cycle....Cold Water (We fill the tub by hand, then rotate dial to Drain/Spin to complete the cycle.

I tried the Reset --Opening/Closing lid method, with no change in results.

Hopefully, you have another magic solution. Thank you
Back to top
Users browsing this topic
Guest (5)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET