Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
Whirlpool oven won't hold temp
Options
Go to last post Go to first unread
Model: RS675PXYH Brand: Whirlpool Age: 5 - 10 years
Previous Topic Next Topic
Clcmbtn  
#1 Posted : Friday, February 6, 2015 3:21:48 PM(UTC)
Clcmbtn

Rank: Member

Groups: Registered
Joined: 2/6/2015(UTC)
Posts: 3
I have replaced the temp sensor (large probe in upper left corner). Is there a thermostat as well? If we set the oven for 350 it only comes up to around 325 and once you open the door the temp lowers and never recovers.
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
denman  
#2 Posted : Saturday, February 7, 2015 1:43:55 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
[COLOR="Blue"] Is there a thermostat as well? [/COLOR]
I do not see one in the parts.

Does the oven show that it is ready or does it stay in pre-heat?

Do both elements work?
On most units the bake and broil elements switch back and forth when in bake and in pre-heat.
THIS FORUM IS DEAD!!!!!!!
Back to top
Clcmbtn  
#3 Posted : Saturday, February 7, 2015 2:07:37 PM(UTC)
Clcmbtn

Rank: Member

Groups: Registered
Joined: 2/6/2015(UTC)
Posts: 3
No it shows that it's ready for the temp set

Both elements are heating up and getting hot.

The broil element works fine when set on broil. Is it possible the lower element is going bad?
Back to top
denman  
#4 Posted : Saturday, February 7, 2015 2:22:07 PM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
[COLOR="Blue"]Is it possible the lower element is going bad?[/COLOR]
Anything is possible but it is very unlikely.
If the element is getting red along it's length then is OK.

Sounds like a control board problem re: the unit thinks it is ready when it is not. Also when the door is opened even though the temperature drops it still thinks it is ready.

Your model number seems to be missing the last digit.
I looked up it with a 1 at the end and it looks like the control board may no longer be available.

If it was a constant low temperature then it could be that the oven temperature just needs calibrating.
THIS FORUM IS DEAD!!!!!!!
Back to top
Clcmbtn  
#5 Posted : Saturday, February 7, 2015 2:38:53 PM(UTC)
Clcmbtn

Rank: Member

Groups: Registered
Joined: 2/6/2015(UTC)
Posts: 3
Last digit is a 0

If the board is N/A I would guess a new unit is in order. Would it be worth a try to recalibrate anyway?
Back to top
denman  
#6 Posted : Sunday, February 8, 2015 2:23:56 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Can't hurt to give it a try.
Below is the operators manual in case you do not have it.
The procedure is on Page 14.
http://www.whirlpool.com/digita...0Guide%20-%203183768.pdf
THIS FORUM IS DEAD!!!!!!!
Back to top
Users browsing this topic
Guest (3)
Similar Topics
Whirlpool oven won't hold temp (Oven Repair (including Ranges and Cooktops))
by trooper 8/24/2010 12:13:01 PM(UTC)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET