3 Pages123> Go to Page...

GE top load washer make grinding noise during agitation and spin, but work fine, just Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
	Brand: GE	Age: 5 - 10 years
Previous Topic Next Topic

dchanson55		#1 Posted : Monday, January 21, 2013 4:11:28 PM(UTC)
Rank: Member Groups: Registered Joined: 1/21/2013(UTC) Posts: 16		I moved mt GE washer to clean under it. when I went to wash a load it started maikng a bad grinding sound. The washer works fine, just makes the noise. I filled the tub with water for a small load of clothes, ran it with no clothes, and there was no noise. If I press down on the tub and turn the agitator it makes the grinding sound. :(
User Profile View All Posts by User View Thanks

Sponsor
	See inside of your appliance - diagrams and part photos for virtually every model. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com

fairbank56		#2 Posted : Monday, January 21, 2013 5:14:53 PM(UTC)
Rank: Advanced Member Groups: Expert Joined: 10/16/2012(UTC) Posts: 3,806 Was thanked: 7 time(s) in 7 post(s)		Model number?
User Profile View All Posts by User View Thanks

dchanson55		#3 Posted : Monday, January 21, 2013 6:03:35 PM(UTC)
Rank: Member Groups: Registered Joined: 1/21/2013(UTC) Posts: 16		Thank you for your reply will get it in the morning, as it is at another house.
User Profile View All Posts by User View Thanks

dchanson55		#4 Posted : Tuesday, January 22, 2013 12:04:13 PM(UTC)
Rank: Member Groups: Registered Joined: 1/21/2013(UTC) Posts: 16		Ge model nm WCSR4170G1WW
User Profile View All Posts by User View Thanks

fairbank56		#5 Posted : Tuesday, January 22, 2013 12:52:05 PM(UTC)
Rank: Advanced Member Groups: Expert Joined: 10/16/2012(UTC) Posts: 3,806 Was thanked: 7 time(s) in 7 post(s)		The model you have is on the list of models that can suffer from a sagging front apron. If the front apron sags, the support assembly under the tub can drop low enough that the motor pulley and/or the drive pulley will rub on the bottom of the washer. You should be able to see this with the front panel removed. There is a front apron bracket service kit available to fix this problem. Eric
User Profile View All Posts by User View Thanks

dchanson55		#6 Posted : Wednesday, January 23, 2013 4:01:14 AM(UTC)
Rank: Member Groups: Registered Joined: 1/21/2013(UTC) Posts: 16		Originally Posted by: fairbank56 The model you have is on the list of models that can suffer from a sagging front apron. If the front apron sags, the support assembly under the tub can drop low enough that the motor pulley and/or the drive pulley will rub on the bottom of the washer. You should be able to see this with the front panel removed. There is a front apron bracket service kit available to fix this problem. Eric Thanks Eric, how do I remove the front panel, and could it be anything else?
User Profile View All Posts by User View Thanks

fairbank56		#7 Posted : Wednesday, January 23, 2013 4:53:48 AM(UTC)
Rank: Advanced Member Groups: Expert Joined: 10/16/2012(UTC) Posts: 3,806 Was thanked: 7 time(s) in 7 post(s)		Insert a putty knife into the top groove of the front panel in line with the lid opening on each side while pulling outward on the panel. Then just lift the panel off. Observe the pulleys while doing a load to determine if this is the problem. If not, try to localize the source of the noise. Eric
User Profile View All Posts by User View Thanks

dchanson55		#8 Posted : Wednesday, January 23, 2013 7:23:07 AM(UTC)
Rank: Member Groups: Registered Joined: 1/21/2013(UTC) Posts: 16		pulled front cover does not look like it is sagging noise is coming from the bottom area where the drive belts are and only with a load of clothes and and water level set for large load
User Profile View All Posts by User View Thanks

fairbank56		#9 Posted : Wednesday, January 23, 2013 9:24:53 AM(UTC)
Rank: Advanced Member Groups: Expert Joined: 10/16/2012(UTC) Posts: 3,806 Was thanked: 7 time(s) in 7 post(s)		So, with a full load, you don't see either pulley hitting the bottom of the washer? Can't really help you any further without seeing/hearing it myself. Can you post a video on youtube? Eric
User Profile View All Posts by User View Thanks

dchanson55		#10 Posted : Thursday, January 24, 2013 3:42:48 AM(UTC)
Rank: Member Groups: Registered Joined: 1/21/2013(UTC) Posts: 16		Originally Posted by: fairbank56 So, with a full load, you don't see either pulley hitting the bottom of the washer? Can't really help you any further without seeing/hearing it myself. Can you post a video on youtube? Eric Yes I can do that, will let you know
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (6)

3 Pages123> Go to Page...