My dishwasher continues to try and drain when there is no longer any water - Appliance Repair Forum

Welcome Guest! You can not login or register.

Notification

Error

My dishwasher continues to try and drain when there is no longer any water Options Email this topic Watch this topic Print this topic » Normal Threaded
Model: SHU3302UC/43	Brand: Bosch	Age: 5 - 10 years
Previous Topic Next Topic

harperatll		#1 Posted : Wednesday, October 31, 2012 7:38:43 PM(UTC)
Rank: Member Groups: Registered Joined: 10/31/2012(UTC) Posts: 3		My Bosch dishwasher continues to try draining when there is no water left in the dishwasher.... diagnostic states water sensor.....where is this located and which part do I need?


User Profile View All Posts by User View Thanks

Sponsor

See inside of your appliance - diagrams and part photos for virtually every model.

Gene		#2 Posted : Thursday, November 1, 2012 3:05:30 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Originally Posted by: harperatll ...diagnostic states water sensor.. How did it show it? Gene.


User Profile View All Posts by User View Thanks

harperatll		#3 Posted : Thursday, November 1, 2012 7:13:27 PM(UTC)
Rank: Member Groups: Registered Joined: 10/31/2012(UTC) Posts: 3		When we did the diagnostic check the Rinse and Hold light stayed on. You can hear the water drain and then the motor keeps trying to drain...:confused:


User Profile View All Posts by User View Thanks

Gene		#4 Posted : Friday, November 2, 2012 4:39:00 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		The temperature sensor aka a NTC is shown as #2 at the diagram. The removal instructions are attached to the post. - The NTC Part number: 165281 Gene. File Attachment(s): heater and NTC.doc (29kb) downloaded 8 time(s).


User Profile View All Posts by User View Thanks

harperatll		#5 Posted : Sunday, November 4, 2012 8:25:48 PM(UTC)
Rank: Member Groups: Registered Joined: 10/31/2012(UTC) Posts: 3		Continuous running of drain pump is not issue anymore. After checking float pump micro switch we are able to run dishwasher on rinse hold/cycle without any problems and completes it's cycle in the 10 minute time frame of which the manual states but when we try to run a regular wash cycle it continues to run for at least four hours (instead of the 135 minutes listed in the manual) and has an occasional flooding out of the front of dishwasher. Dishwasher does not seem to get hot during the wash cycle. Is the NTC part still the problem?


User Profile View All Posts by User View Thanks

Gene		#6 Posted : Tuesday, November 6, 2012 3:05:05 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		There are 3 parts in the heating circuit. They are: the control module, the heater and the NTC/limit thermostat. Most common cause of such problem with all Bosch dishwashers for number of years has been a faulty control module . The last 2 numbers in the model number which you posted does not match any available. The closest is 14. That's why I'm not able to verify for you the part number for the control module. Check the model number and repost it. Gene.


User Profile View All Posts by User View Thanks

Users browsing this topic
Guest (2)

Forum Jump

You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Important Information: The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies. More Details Close