2 Pages12> Go to Page...

Washer not agitating or spinning help please Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: WBSR3140G1WW	Brand: GE	Age: 1 - 5 years
Previous Topic Next Topic

oxtart		#1 Posted : Monday, September 10, 2012 6:54:23 AM(UTC)
Rank: Member Groups: Registered Joined: 9/10/2012(UTC) Posts: 11		Like the title says. My moms GE stopped agitating or spinning fills and empties no problem. Any suggestions. Thanks
User Profile View All Posts by User View Thanks

Sponsor
	See inside of your appliance - diagrams and part photos for virtually every model. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com

Simon / APP Team		#2 Posted : Monday, September 10, 2012 12:14:15 PM(UTC)
Rank: Advanced Member Groups: APP Team Joined: 2/12/2012(UTC) Posts: 5,556		HI. Using the putty knife release two clips at the top and remove the front panel. Observe the indicator light on the motor control. Count the flashes. A lot of times it's the bad motor Part number: WH20X10057 Here are the breakdown diagrams and Replacement parts for General Electric WBSR3140G1WW WASHER | AppliancePartsPros.com Post the results. Simon.
User Profile View All Posts by User View Thanks

oxtart		#3 Posted : Monday, September 10, 2012 12:28:39 PM(UTC)
Rank: Member Groups: Registered Joined: 9/10/2012(UTC) Posts: 11		Thanks for the response. Do i just turn it on to get the lights to flash?
User Profile View All Posts by User View Thanks

Simon / APP Team		#4 Posted : Monday, September 10, 2012 1:37:18 PM(UTC)
Rank: Advanced Member Groups: APP Team Joined: 2/12/2012(UTC) Posts: 5,556		Yes. Let it run for a few. Simon.
User Profile View All Posts by User View Thanks

oxtart		#5 Posted : Monday, September 10, 2012 4:25:30 PM(UTC)
Rank: Member Groups: Registered Joined: 9/10/2012(UTC) Posts: 11		so i took off the front panel and clear as day the belt was shredded and had fell off. also the light was flashing 4 times. however i changed the settings on the washer and i couldnt get the spindle attached to the motor to spin.
User Profile View All Posts by User View Thanks

Simon / APP Team		#6 Posted : Monday, September 10, 2012 5:03:37 PM(UTC)
Rank: Advanced Member Groups: APP Team Joined: 2/12/2012(UTC) Posts: 5,556		Hi. Unplug the washer and check resistance of the mode shifter at room temp. 98 ohm. If the shifter coil is open - replace it and the belt. The sifter Part number: WH38X10017 The belt WH01X10302 What do you mean by spindle attached to the motor (the motor shaft?) Simon.
User Profile View All Posts by User View Thanks

oxtart		#7 Posted : Tuesday, September 11, 2012 3:34:59 AM(UTC)
Rank: Member Groups: Registered Joined: 9/10/2012(UTC) Posts: 11		The motor part that the belt attaches to spins freely and the the big wheel the belt attaches to also spins freely but when i turn the mode dial to the spin position the motor doesnt seem to activate. Is that because the belt is off? Also what does the 4 x flashing light mean?
User Profile View All Posts by User View Thanks

Simon / APP Team		#8 Posted : Tuesday, September 11, 2012 8:33:45 AM(UTC)
Rank: Advanced Member Groups: APP Team Joined: 2/12/2012(UTC) Posts: 5,556		Hi. 4 blinks means mode shifter problem.Check the resistance at the plug C7 (red/yellow). Simon.
User Profile View All Posts by User View Thanks

oxtart		#9 Posted : Wednesday, September 12, 2012 3:58:03 AM(UTC)
Rank: Member Groups: Registered Joined: 9/10/2012(UTC) Posts: 11		Ok so i tested the mode shifter and got no reading so I assume its dead. I will order new shifter ,belt and belt install kit. Can you point me in direction of instructions on changing out the mode shifter. Thanks for all your help.
User Profile View All Posts by User View Thanks

Gene		#10 Posted : Wednesday, September 12, 2012 11:44:30 AM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Just to add my 2 cents... Sometime in such situation the motor has to be replaced too. In order to determine if the motor in your washer has to be replaced we need the 12 characters (starting with 175) part number from the motor label. Also check the label on the top cover of the motor. If the part number on this label is different, post it too. The replacement instructions are attached. Gene. File Attachment(s): Lid switch removal.doc (248kb) downloaded 7 time(s). The cover-lid removal.doc (311kb) downloaded 6 time(s). The tub cover removal.doc (617kb) downloaded 5 time(s). The tub removal - 2.doc (517kb) downloaded 7 time(s). The tub removal - 1.doc (915kb) downloaded 6 time(s). The shaft and mode shifter removal.doc (259kb) downloaded 10 time(s). The shaft and mode shifter removal - 1.doc (1,344kb) downloaded 6 time(s). The shaft and mode shifter removal - 2.doc (1,223kb) downloaded 6 time(s). The shaft and mode shifter removal - 3.doc (779kb) downloaded 6 time(s).
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (4)

2 Pages12> Go to Page...