Rank: Member
Groups: Registered
Joined: 9/8/2012(UTC)
Posts: 6
|
Following power drop outs, Normal light blinking and attempted reset by turning off AC to DW. From threads on site, appeared to be issue with control board. Ordered from AppPartsPros and installed. Seemed to work ok for about two weeks, then normal light flashing again. They sent a replacement control board, which I installed.
Problem now is that, while I can select all cycles (Heavy, Normal, Light, Rinse Only) via panel, I cannot select Hi Temps Scrub, Energy Saver Dry, Control Lock. I can only get the Delay to select the 4 hour function.
Dishwasher will run through the cycles (wash and rinse), but the Dry light and Clean lights never come on.
Any suggestions, other than a large sledge?
Thanks
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 9/8/2012(UTC)
Posts: 6
|
Dishwasher DOES NOT run full cycle - It will only wash and when done, the normal light blinks. Have to turn off the breaker, wait a few minutes, turn it back on, select Rinse and Start. Not a very automatic way to clean dishes....:confused:
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455
Was thanked: 4 time(s) in 4 post(s)
|
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 9/8/2012(UTC)
Posts: 6
|
Hi -
Color is Black (BL0)
Thanks,
Wayne
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455
Was thanked: 4 time(s) in 4 post(s)
|
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 9/8/2012(UTC)
Posts: 6
|
Thanks for the help. Just wanted to update the "ghost" actions. DW will run through wash cycle, then revert to blinking NORMAL - as I noted before. BUT, there is a new twist. If I open the Door after it starts blinking, and wait a bit, the Normal stops blinking. If I then close the door, press Start, it continues with the RINSE cycle (of course, it never shows DRY or Clean after it is done rinsing)
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455
Was thanked: 4 time(s) in 4 post(s)
|
You still may want to replace the console first.
Gene.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 9/8/2012(UTC)
Posts: 6
|
I ordered and received the panel, but did not have time to install yet (fortunately). There are now NO lights on panel, when any key is pressed. I have to get a new meter to test for ac at door switch, etc., but am wondering if you could provide any DC measurements, in case problem is with the PS under the DW.
Thanks
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455
Was thanked: 4 time(s) in 4 post(s)
|
I'm afraid I did not get clear what did you call "PS".
No lights on the panel can be related to the panel problems.
Gene.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 9/8/2012(UTC)
Posts: 6
|
Gene,
The final chapter: It was dead because the thermal fuse finally gave out. Replaced it this morning and cycled through a full clean cycle. I give you a high five for the console - wish I had posted before ordering the control board.
Anyway, many thanks (especially from the wife!)
|
|
|
|
|
|
Forum Jump
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.
Important Information:
The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close
