Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
2 Pages12>
Neptune Washer Problem
Options
Go to last post Go to first unread
Model: MAH9700AWW Brand: Maytag Age: 5 - 10 years
Previous Topic Next Topic
Firepike24  
#1 Posted : Monday, March 12, 2012 11:16:36 AM(UTC)
Firepike24

Rank: Member

Groups: Registered
Joined: 3/12/2012(UTC)
Posts: 7
I have a Neptune washer that gives me a 3E error code and stops in the middle of a cycle. When I try to restart the washer I can hear the something "click" inside and it stops again. What do I need to replace?
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
Simon / APP Team  
#2 Posted : Monday, March 12, 2012 12:49:22 PM(UTC)
Simon / APP Team

Rank: Advanced Member

Groups: APP Team
Joined: 2/12/2012(UTC)
Posts: 5,556
Hi.

Generally the 3E code means bad HALL sensor or wiring harness to the control board. Read the attached file.


The sensor and motor assembly part number is AP4211146.
.

The internet store shows we're out of stock but we should have 4. Talk to our rep at the call center.

Please post results.
File Attachment(s):
TDL-0078A-B mah9700aww.pdf (84kb) downloaded 21 time(s).
Back to top
Firepike24  
#3 Posted : Tuesday, March 13, 2012 7:05:39 AM(UTC)
Firepike24

Rank: Member

Groups: Registered
Joined: 3/12/2012(UTC)
Posts: 7
I checked the connections and they seem to be fine. The washer always seems to stop and throw the code at the end of the rinse cycle when it is trying to start the spin cycle. How do I know if I need a new wiring harness?
Back to top
Simon / APP Team  
#4 Posted : Tuesday, March 13, 2012 10:50:59 AM(UTC)
Simon / APP Team

Rank: Advanced Member

Groups: APP Team
Joined: 2/12/2012(UTC)
Posts: 5,556
Hello, Firepike 24.

If you pulled off and reconnected all the wires and plugs at the motor sensor and control board and the washer still gives you 3E code most likely you looking at replacing the motor and sensor assembly.

The motor Part number: AP4044223
Part number: AP4044223
.

Remember, that you can always return any unused parts purchased from APP even if they have been installed.

Good luck and keep us posted.
Back to top
Markram  
#5 Posted : Tuesday, March 13, 2012 4:05:23 PM(UTC)
Markram

Rank: Member

Groups: Registered
Joined: 3/7/2012(UTC)
Posts: 48
Originally Posted by: Firepike24 Go to Quoted Post
I have a Neptune washer that gives me a 3E error code and stops in the middle of a cycle. When I try to restart the washer I can hear the something "click" inside and it stops again. What do I need to replace?



Error code 3E is Over current detected in motor.

These units have had issues with leaks causing water to get onto electrical components, this could have caused an issue with motor, or wiring connections to it, or speed sensor.

Check the area for moisture.

Also check the motor windings, speed sensor, wiring connections also, and it can sometimes be the control board if these all test good.

good luck, you can find the tests for the motor windings, speed sensor and such on the tech manual inside of unit, behind the control panel or on back of unit in flat plastic bag.

If there was water in the motor and speed sensor area, then the over current could have been caused by water... seek the source of the leak, remedy it, then use a blow dryer on medium heat, to dry electrical connections, but be careful to not get anything too hot.
Back to top
Firepike24  
#6 Posted : Thursday, March 15, 2012 11:08:42 AM(UTC)
Firepike24

Rank: Member

Groups: Registered
Joined: 3/12/2012(UTC)
Posts: 7
I got the new motor today, kudos to the fast shipping. What is the easiest way to get the old one out?
Back to top
Simon / APP Team  
#7 Posted : Thursday, March 15, 2012 1:33:06 PM(UTC)
Simon / APP Team

Rank: Advanced Member

Groups: APP Team
Joined: 2/12/2012(UTC)
Posts: 5,556
Hello.

Here are the instructions:

Unplug the washer.
Remove the back cover.
Remove the vent hose on either side.
Rotate the spinner to locate the slot.
Insert the rubber handled tool or object to lock the spinner.
Remove the 19mm motor nut.
Grasp the rotor on the sides and pull it from the shaft.
Remove motor wiring connectors.
Remove six 10mmbolts holding stator coil. There are alignment pins for the stator re-installation.
Reinstall everything in reverse order.

Thank you and good luck.
Back to top
Firepike24  
#8 Posted : Wednesday, March 21, 2012 6:17:19 PM(UTC)
Firepike24

Rank: Member

Groups: Registered
Joined: 3/12/2012(UTC)
Posts: 7
First motor was not compatible. Second motor was received damaged. Third motor is on it's way. I did try the damaged motor and I was still getting a 3E error code. What is wrong with this thing?
Back to top
Simon / APP Team  
#9 Posted : Wednesday, March 21, 2012 6:41:29 PM(UTC)
Simon / APP Team

Rank: Advanced Member

Groups: APP Team
Joined: 2/12/2012(UTC)
Posts: 5,556
Hi.

Please wait for motor#3 to arrive. Sorry for any inconvenience.

Post results.
Back to top
Firepike24  
#10 Posted : Thursday, March 22, 2012 1:13:11 PM(UTC)
Firepike24

Rank: Member

Groups: Registered
Joined: 3/12/2012(UTC)
Posts: 7
New motor is in and still won't spin. Please help!!
Back to top
Users browsing this topic
Guest (7)
Similar Topics
maytag neptune washer problem (Washer Repair)
by jtaend 10/20/2010 6:46:15 PM(UTC)
2 Pages12>
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET