9 Pages«<56789> Go to Page...

Gas dryer running but no heat Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: LGR7648KQ1	Brand: Whirlpool	Age: 5 - 10 years
Previous Topic Next Topic

trmart		#61 Posted : Thursday, February 17, 2011 4:57:37 AM(UTC)
Rank: Member Groups: Registered Joined: 2/15/2011(UTC) Posts: 4		Got a new coil kit last night, installed it, and the dryer works! Thanks
User Profile View All Posts by User View Thanks

Gene		#62 Posted : Thursday, February 17, 2011 12:09:36 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		You are welcome. I'm glad you were able to fix it. A bad coils is the most common problem with all gas dryers. Gene.
User Profile View All Posts by User View Thanks

oasis		#63 Posted : Saturday, February 19, 2011 10:41:31 AM(UTC)
Rank: Member Groups: Registered Joined: 2/14/2011(UTC) Posts: 10		Gene, I have checked the exhaust pipe and everything is clear. The problem still exist, which it takes 2 40 plus min to dry the clothing. What else can I check? Thanks!
User Profile View All Posts by User View Thanks

Gene		#64 Posted : Saturday, February 19, 2011 3:07:00 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Originally Posted by: oasis ...I have checked the exhaust pipe and everything is clear... Can you be more detailed on how did you do it? Remove the rear cover and the lint chute (#1 on the diagram). Clean the lint chute and check the blower wheel. Try to disconnect the vent hose from the dryer and run a load to see if there is any difference. Longer time to dry in most cases caused by restricted air flow because all moister stays inside the dryer. Gene.
User Profile View All Posts by User View Thanks

oasis		#65 Posted : Monday, February 21, 2011 4:10:31 PM(UTC)
Rank: Member Groups: Registered Joined: 2/14/2011(UTC) Posts: 10		I just took the pipe off the wall and had it run for a few minutes and hot air does come off the pipe. How should I test the blower wheel?
User Profile View All Posts by User View Thanks

Gene		#66 Posted : Monday, February 21, 2011 7:43:01 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Take it off the dryer and run a full load to see how long it will take. Gene.
User Profile View All Posts by User View Thanks

oasis		#67 Posted : Monday, February 21, 2011 8:07:29 PM(UTC)
Rank: Member Groups: Registered Joined: 2/14/2011(UTC) Posts: 10		I will give that a try tonight. Thanks!
User Profile View All Posts by User View Thanks

oasis		#68 Posted : Monday, February 21, 2011 10:24:26 PM(UTC)
Rank: Member Groups: Registered Joined: 2/14/2011(UTC) Posts: 10		Gene, I have cleaned out the link chute and checked the blower wheel (it seems ok). But still need to run more than 2 cycles to dry clothing (with disconnected vent hose). What else can I check?
User Profile View All Posts by User View Thanks

diamondjim007		#69 Posted : Tuesday, February 22, 2011 12:33:40 AM(UTC)
Rank: Member Groups: Registered Joined: 2/21/2011(UTC) Posts: 1		My dryer is acting the same way. It fires, but doesn't refire. I've checked the vent and its open and blowing freely. I'm not sure what I should check next. Please help
User Profile View All Posts by User View Thanks

Gene		#70 Posted : Tuesday, February 22, 2011 1:08:15 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Originally Posted by: oasis Gene, I have cleaned out the link chute and checked the blower wheel (it seems ok). But still need to run more than 2 cycles to dry clothing (with disconnected vent hose). What else can I check? Remove the plug on the left side of the front panel and check how the flame is reigniting. If it does not reignite every time when the igniter glows then the problem is a bad gas valve coils. If it does reignite properly but the flame stays on much less than a minute, the problem can be a bad high limit thermostat (#15 on the diagram) or a clogged (rusted) lint screen. - The coil kit Part number: AP3094251 - The high limit thermostat Part number: AP3084674 - The lint screen Part number: AP3748781 Gene.
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (3)

Similar Topics

Gas Dryer running but no heat (Dryer Repair) by cpenn42 8/26/2011 4:50:25 PM(UTC)

9 Pages«<56789> Go to Page...