Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
2 Pages12>
Oven/Broiler Inop but stovetop and dispaly works
Options
Go to last post Go to first unread
Model: ES300 Brand: Frigidaire Age: 5 - 10 years
Previous Topic Next Topic
eleatherman  
#1 Posted : Monday, February 7, 2011 1:09:01 PM(UTC)
eleatherman

Rank: Member

Groups: Registered
Joined: 2/7/2011(UTC)
Posts: 6
When I turnon the oven or broiler the control displays operates indicating that the unit is functioning. But the elements never heat up. The stove top appears to be working fine. Where should i start in touble shooting the problem?
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
denman  
#2 Posted : Wednesday, February 9, 2011 1:35:35 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
I think ES300 is the control type and not a model number.
Please look for a model number.
Model Number Locator

Some units but not all have a thermal cut-out (fuse) in the heating element circuit.
THIS FORUM IS DEAD!!!!!!!
Back to top
eleatherman  
#3 Posted : Wednesday, February 9, 2011 4:28:29 AM(UTC)
eleatherman

Rank: Member

Groups: Registered
Joined: 2/7/2011(UTC)
Posts: 6
Model # is FEFL78CQA
Back to top
denman  
#4 Posted : Wednesday, February 9, 2011 6:55:52 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Here is the parts breakdown
Replacement parts for FRIGIDAIRE FEFL78CQA Frigidaire/electric Range | AppliancePartsPros.com

Here is the wiring diagram
http://manuals.frigidaire.com/prodinfo_pdf/Springfield/316255333.pdf

When I turnon the oven or broiler the control displays operates indicating that the unit is functioning.
If you mean that it comes ready or shows a temperature higher than set point , it could be the temperature probe (Item 37 in Section 2)
Here is a good link with info on how to check it.
http://www.applianceaid.com/elecrange.html
Check out 7, 8, 20 and 21.

If the probe is OK then it could be a bad connection, a wire burned off or the control board/clock (Item 20 in Section 1).

The following may also come in handy.
http://frigidaireservicetips.com/pdfs/344_UpdateforElectricFreestandingElectricRanges_Rev.pdf
THIS FORUM IS DEAD!!!!!!!
Back to top
eleatherman  
#5 Posted : Wednesday, February 9, 2011 10:30:25 AM(UTC)
eleatherman

Rank: Member

Groups: Registered
Joined: 2/7/2011(UTC)
Posts: 6
The display indicates the unit is working and preheating but the element never gets hot. Or the unit indicates that the broiler is heating but again ite never gets hot. I first thought an element was going bad but do not think both would go out at the same time. It would appear that either a reay is stuck or a fuse is blown, does that sound feasible? I wil check the probe though for failure.
Back to top
denman  
#6 Posted : Thursday, February 10, 2011 2:13:15 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
[COLOR="DarkRed"]It would appear that either a reay is stuck or a fuse is blown, does that sound feasible?[/COLOR]
The wiring diagram does not show a fuse or a hi-limit thermostat.

So the problem is likely on the control board could be a set of relay contacts are burned out or the electronics that control the relay are shot.
THIS FORUM IS DEAD!!!!!!!
Back to top
eleatherman  
#7 Posted : Thursday, February 10, 2011 1:08:47 PM(UTC)
eleatherman

Rank: Member

Groups: Registered
Joined: 2/7/2011(UTC)
Posts: 6
Originally Posted by: denman Go to Quoted Post
[COLOR="DarkRed"]It would appear that either a reay is stuck or a fuse is blown, does that sound feasible?[/COLOR]
The wiring diagram does not show a fuse or a hi-limit thermostat.

So the problem is likely on the control board could be a set of relay contacts are burned out or the electronics that control the relay are shot.

I assume the control panel is part #AP3758650 from the diagrams. Thanks for the help.
Back to top
denman  
#8 Posted : Friday, February 11, 2011 3:58:30 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
No that is the panel not the control board.

The control board/clock is Item 20 in Section 1 - AP5176341

You may also need an overlay Item 20A - AP3219801
It is a stick on and sometimes gets ruined trying to get it off the old control.
THIS FORUM IS DEAD!!!!!!!
Back to top
eleatherman  
#9 Posted : Friday, February 11, 2011 4:57:25 AM(UTC)
eleatherman

Rank: Member

Groups: Registered
Joined: 2/7/2011(UTC)
Posts: 6
Thanks, I'll order them today.
Back to top
eleatherman  
#10 Posted : Thursday, February 24, 2011 6:03:33 AM(UTC)
eleatherman

Rank: Member

Groups: Registered
Joined: 2/7/2011(UTC)
Posts: 6
The parts arrived yesterday. Installation took 15 minutes. Now have both bake and broil, oven working fine. It was the control panel. Thanks for the help.
Back to top
Users browsing this topic
Guest (11)
2 Pages12>
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET