Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
GE Dishwasher Will Not Fill
Options
Go to last post Go to first unread
Model: PDW8400J10WW Brand: GE Age: 1 - 5 years
Previous Topic Next Topic
kodiak_dude  
#1 Posted : Wednesday, September 8, 2010 2:05:24 PM(UTC)
kodiak_dude

Rank: Member

Groups: Registered
Joined: 9/8/2010(UTC)
Posts: 2
I have a GE dishwaher that was not emptying out the tub. I installed a new computer module in it and it worked fine for about a week. Now it will not fill with water. If I run a rinse cycle I can hear the motor/pump for the wash cycle kick in and the drain pump kicks in fine. It just will not fill with water. The unit is less than 5 years old and I am trying to find ideas on what could cause it not to fill with water. Any help or ideas that anyone could give would be appreciated.

Thanks
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
denman  
#2 Posted : Thursday, September 9, 2010 4:32:22 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Here are your parts
Replacement parts for General Electric PDW8400J10WW Dishwasher | AppliancePartsPros.com

First I would check the overfill (flood) switch (Item 308 in Section 2).
Sometimes the float can get stuck in the upo position so the unit thinks it is already full.

Next I would check that the fill valve is getting power when it should.
If not check across the fill valve/flood switch combo. They are wired in series.

If the valve is getting power then the problem is either:
1. The valve is shot.
2. The screen filter on the input side of the valve is clogged up. Remove the valve from the unit and clean/check the filter screen. Do not permanently remove it from the valve. It is there to keep crud out of the valve which could hold it open andf cause a flood.
THIS FORUM IS DEAD!!!!!!!
Back to top
badbackguy  
#3 Posted : Thursday, September 9, 2010 8:20:22 AM(UTC)
badbackguy

Rank: Member

Groups: Registered
Joined: 1/7/2010(UTC)
Posts: 29
I would do as denman said, here is a link that should help walk you thru testing the float switch and water inlet valve. Dishwasher Float & Water Inlet Repair Video
Back to top
kodiak_dude  
#4 Posted : Tuesday, September 14, 2010 9:42:04 AM(UTC)
kodiak_dude

Rank: Member

Groups: Registered
Joined: 9/8/2010(UTC)
Posts: 2
Hi guys, thanks for the ideas, advise and the link to the video. It turned out they float switch was bad. Once I replaced that it was good to go and my wife was super happy. You guys were spot on.

Thanks again.
Back to top
Users browsing this topic
Guest (5)
Similar Topics
GE dishwasher will not fill with water! (Dishwasher Repair)
by joyelizabeth 12/3/2010 2:36:57 PM(UTC)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET