Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

Options
Go to last post Go to first unread
Tara G  
#1 Posted : Wednesday, December 9, 2009 12:58:53 PM(UTC)
Tara G

Rank: Member

Groups: Registered
Joined: 11/30/2009(UTC)
Posts: 3

I tried to start my dryer last week and it made a pulsing quiet buzzing noise. I have since torn the entire thing apart, searched extensively on the web and concluded that it was most likely that the motor had gone out. I ordered a new motor and blower which arrived today.

I have installed the new motor/blower, reconnected all wiring (except for the interior light) and just tried to start it. Hoping to hoot, holler, and celebrate, I was extremely frustrated when it only made the same exact sound as before. Is there something else I need to reassemble before it will work? Or did I just buy a new motor/blower for nothing? Any ideas on what else it could be?

Thank you!
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
Gene  
#2 Posted : Wednesday, December 9, 2009 4:18:02 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
There are two parts I would check: the broken belt switch (#5 on the diagram) and the thermal fuse (#59 on the diagram).

- The broken belt switch Part number: AP3094230
Part number: AP3094230



- The thermal fuse Part number: AP3133489
Part number: AP3133489



Here is the wiring sheet.

Gene.
Tara G  
#3 Posted : Wednesday, December 9, 2009 4:42:16 PM(UTC)
Tara G

Rank: Member

Groups: Registered
Joined: 11/30/2009(UTC)
Posts: 3

Thank you Gene.
How would I go about 'checking' these? Should I be checking continuity?
Gene  
#4 Posted : Wednesday, December 9, 2009 4:51:42 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
Quote:
... Should I be checking continuity?...


Yes, that's right.

Gene.
TheDragon  
#5 Posted : Wednesday, December 9, 2009 5:09:23 PM(UTC)
TheDragon

Rank: Member

Groups: Registered
Joined: 12/9/2009(UTC)
Posts: 7

try to turn the end of cycle signal knob to silent
and/or try to make sure the timer is full off (make it click)
I had the same sound - thought it was bad wires arching in the outlet
then thought it was bad wires in the electric control panel
then tracked the sound (using a home made stethoscope)
to the little speaker that emits the end of cycle beep/buzzer
even that was the 'source' of the sound - still not sure what the cause was
I replaced the circuit board because I lost my heat -
fixed the sound - still trying to fix the no heat
Tara G  
#6 Posted : Friday, December 11, 2009 5:37:45 AM(UTC)
Tara G

Rank: Member

Groups: Registered
Joined: 11/30/2009(UTC)
Posts: 3

thank you for the advice. I have been without a dryer for near three weeks now and finally broke down and took it to the repair shop. I ran out of clean socks a few days ago :( I asked them to call me and they said I could be present while they work on it. Hopefully I will get a lesson along with my bill.
Thanks!
Users browsing this topic
Guest (2)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.