Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

2 Pages12>
Options
Go to last post Go to first unread
Steve A  
#1 Posted : Friday, October 2, 2009 11:11:23 AM(UTC)
Steve A

Rank: Member

Groups: Registered
Joined: 9/5/2008(UTC)
Posts: 10

I'm pretty sure I need to replace the float switch in this dishwasher but I'm finding it very difficult to access. Are there instructions available to show how to get at this? (Drain pump runs continuously, cycles do not advance, diagnostic test stays on 0 and cycles don't advance in diagnostics either.)
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
Gene  
#2 Posted : Friday, October 2, 2009 2:59:08 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
Have you checked the base of the dishwasher for a possible water leak?

Gene.
Steve A  
#3 Posted : Friday, October 2, 2009 6:25:49 PM(UTC)
Steve A

Rank: Member

Groups: Registered
Joined: 9/5/2008(UTC)
Posts: 10

I don't see any leaks in the base.
Gene  
#4 Posted : Friday, October 2, 2009 7:37:09 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
You have to remove the dishwasher from the cabinet and remove the left side panel. This job is not too difficult.

- The level switch assembly Part number: AP2802390
Part number: AP2802390


Gene.
rupert  
#5 Posted : Saturday, October 3, 2009 1:58:02 AM(UTC)
rupert

Rank: Member

Groups: Registered
Joined: 10/3/2009(UTC)
Posts: 1

Hi, Ive got similar problems. I cant remove side panel till I take off ther top panel. I just cant see how to get the top off. I understand I'm looking for clips to push or similar. Can't see anything that will push, or squeeze!

Are they on the back? Can anyone a give precise answer ( Mine is an SGS 4012.

Apologies to original questioner, but hope this helps.


Rupert
Steve A  
#6 Posted : Saturday, October 3, 2009 6:24:53 AM(UTC)
Steve A

Rank: Member

Groups: Registered
Joined: 9/5/2008(UTC)
Posts: 10

In the past, occasionally a small amount of grayish water has leaked from the machine (probably fewer than one cycle in 50) and I do have seepage into the tub which sometimes becomes visible if the machine isn't run for a couple of days.
Steve A  
#7 Posted : Saturday, October 3, 2009 6:36:46 AM(UTC)
Steve A

Rank: Member

Groups: Registered
Joined: 9/5/2008(UTC)
Posts: 10

Originally Posted by: Gene Go to Quoted Post
You have to remove the dishwasher from the cabinet and remove the left side panel. This job is not too difficult.

- The level switch assembly Part number: AP2802390
Part number: AP2802390


Gene.

Gene,

Sorry, didn't see your reply. Thanks. I had tried to remove that panel but was unsuccessful. I'll try again.
Gene  
#8 Posted : Saturday, October 3, 2009 3:50:38 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
The side panel is secured with a few screws around.

Gene.
Steve A  
#9 Posted : Wednesday, October 7, 2009 10:38:17 AM(UTC)
Steve A

Rank: Member

Groups: Registered
Joined: 9/5/2008(UTC)
Posts: 10

Replacement of the level switch assembly has fixed the problem--thanks. Now I have to stop water from seeping in I believe through the drain hose even though I restored the loop in the hose higher than the drain.
Gene  
#10 Posted : Wednesday, October 7, 2009 12:14:16 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
It can be a bad water inlet valve as well.

Gene.
Users browsing this topic
Guest (3)
2 Pages12>
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.