Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
2 Pages<12
Refrigerator repair question
Options
Go to last post Go to first unread
Model: GTS22KBMBRWW Brand: GE Age: 5 - 10 years
Previous Topic Next Topic
bthlonewolf  
#11 Posted : Monday, September 14, 2009 6:00:46 AM(UTC)
bthlonewolf

Rank: Member

Groups: Registered
Joined: 9/12/2009(UTC)
Posts: 24
Richappy -- thanks! Could I ask you to clarify?

I see the 3 pin connector on the motherboard (which you can see in the top pict above, bottom right), and 2 of those are marked Line and Compressor. The middle one is marked DEFR (defrost?). Should I jumper these two Line/Compressor? Do I then leave the power connector on the board unplugged or do I plug it back in?

I considered making a hookup directly to the 3 pins on the compressor, but I'm up for whichever is easier.
Back to top
richappy  
#12 Posted : Monday, September 14, 2009 8:33:54 AM(UTC)
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
Just leave the power connector unplugged, then plug in the fridg. You can monitor the compresser current through this jumper.
Back to top
bthlonewolf  
#13 Posted : Monday, September 14, 2009 2:55:37 PM(UTC)
bthlonewolf

Rank: Member

Groups: Registered
Joined: 9/12/2009(UTC)
Posts: 24
OK -- going to try this when I get home later but I looked at it briefly on my way past -- the way the connector is (some kind of molex looking connector) is very tight ... I guess I can remove the connectors from the plastic housing and jumper there, not sure how else I can get a good connection... I'll post back later. Thx!
Back to top
bthlonewolf  
#14 Posted : Tuesday, September 15, 2009 7:32:49 AM(UTC)
bthlonewolf

Rank: Member

Groups: Registered
Joined: 9/12/2009(UTC)
Posts: 24
I jumped the comp/line pins, plugged it in, and the compressor started right up, no out of the ordinary sounds or anything.

It's a good bet that the problem is just with the board -- I wish I could desolder and put in a new relay, but the board looks quite toasted in that section and doesn't look salvageable. I'll post back what happens w/ the board...
Back to top
marz7142  
#15 Posted : Thursday, October 13, 2011 3:43:33 AM(UTC)
marz7142

Rank: Member

Groups: Registered
Joined: 10/13/2011(UTC)
Posts: 1
I have the same model, same problem, same burnt relay on solder side of motherboard. What was the problem??? thanx.
Back to top
richappy  
#16 Posted : Thursday, October 13, 2011 7:46:28 AM(UTC)
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
The original problem, the manufacturer did not wave solder the board properly and the thin solder at the power relay acted as a fuse and blew open. Usually, re-soldering will fix it, no relay replacement necessary.
Back to top
Users browsing this topic
Guest (4)
Similar Topics
refrigerator repair question (Refrigerator & Freezer Repair)
by tlavacque 8/31/2013 10:25:56 AM(UTC)
Refrigerator Repair Question (Refrigerator & Freezer Repair)
by allantag 8/24/2012 10:17:04 AM(UTC)
GE Refrigerator Repair Question (Refrigerator & Freezer Repair)
by jgolfaholic 5/17/2011 7:59:47 PM(UTC)
2 Pages<12
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET